circuit
Latest
NEC's fancy new wiring technology could lead to slimmer LCD HDTVs
While it's pretty much a given that HDTVs are going to slim down from one CES / CEDIA to another, you probably wouldn't think that wiring schemes would be the catalyst for making it happen. NEC Electronics has just revealed a "next-generation connection technology for the circuitry in large LCDs" that will enable big screens to get all the more thinner. Essentially, the tech is "specific to the wiring used to transfer signals from the image processing board to the driver chips that are fitted to the periphery of the LCD panel and control the pixels." Currently, a Full HD 37-inch LCD TV requires right around 21 wires to make the magic happen; with NEC's approach, just 8 would be needed. The company expects to have a "practical version" ready to roll sometime in 2009, so we're totally expecting credit card-thin LCDs in January 2010.
Flying plasmonic lens system could lead to denser chips / disks
Last we heard, IBM was busy extending optical lithography down to 30-nanometers in order to keep Moore's Law intact, and some two years later, the process is still being honed by engineers at the University of California, Berkeley. Reportedly, gurus there with IQs far greater than ours have developed a new patterning technique (plasmonic nanolithography) that could make "current microprocessors more than 10 times smaller, but far more powerful." Additionally, professor Xiang Zhang asserts that this same technology could eventually "lead to ultra-high density disks that could hold 10 to 100 times more data than disks today." The secret to the madness is a flying plasmonic head, which is compared to the arm and stylus of an LP turntable; the setup enables researchers to "create line patterns only 80-nanometers wide at speeds up to 12-meters per second, with the potential for higher resolution detail in the near future." In layman's terms? That CPU you purchased last month will, in fact, be old hat in due time.[Via Slashdot]
Integrated circuit turns 50, now isn't that nifty?
Hard to believe that Jack Kilby's unsightly concoction (pictured above) turned 50 yesterday, but it's true. Half a century ago, Mr. Kilby crafted the integrated circuit, which ended up having a monumental impact on taking computers from warehouse-sized to, well, not-warehouse-sized. As the story goes, the very first microchip was demonstrated on the 12th of September in 1958, and it passed its first test: "producing a sine wave on an oscilloscope screen." Safe to say we all know how things progressed from there. Here's to you, IC -- and here's to 50 more.[Via MAKE]
Video: Furby Gurdy makes "music," trips you out
The Nervous Squirrel's Furby Gurdy (version 2) isn't the first music maker we've seen that's better understood when viewed during an out-of-body experience, but it's certainly one of the strangest. The circuit bent Furby sequencer, which is linked to a Korg SQ-10 in the demonstration vid after the break, combines centuries-old musical methods with some of the strangest characters to ever grace planet Earth. We could talk for hours on end and still not do this thing justice, so just click through and mash play to see what we're referring to. We're warning you, though -- we haven't seen anything this weird since Smash Mouth's lead singer showed up at an Intel press event.[Via Hack-A-Day]
iPosture annoys you when you slouch, does so because it loves you
Mama always said you'd regret slouching one day, and while you've still got a few decades left before ultimately determining whether the sage-like advice was right or wrong, why take chances? The iPosture does the same thing as wearable posture reminders that we've seen in the past, but this one does so in a much more discrete fashion. The diminutive nano-sensor detects when your angle deviates just three degrees from the optimal position for greater than a minute, after which it emits a warning to straighten you out. Users insistent on keeping it crooked can turn the device off by powering it down, removing it or flinging it furiously into a wall. Life's next big nuisance will be shipping soon for $99.95.[Thanks, Eric]
Researchers get one step closer to all-nanowire sensors
The latest in nanowire research has a crew at the University of California, Berkeley creating the very first integrated circuit "that uses nanowires as both sensors and electronic components." By utilizing a so-called "simple" printing technique, the researchers were able to create a batch of uniform circuits that could one day serve as image sensors. According to Ali Javey, an electrical-engineering professor at the institution, the goal is to "develop all-nanowire sensors" which could be used in a wide array of applications, and the benefit of using 'em is their exceptionally high level of sensitivity. In due time, the gurus would like to make everything on the circuit printable, though we have this strange feeling we won't be seeing any actual results from all of this for years to come.
DeepNote Guitar Hero bot reveals its secrets on video
Don't even try to deny it -- you've been holding one mean grudge against that ridiculously accurate DeepNote bot ever since you saw it dominate Guitar Hero in mid-July. Really though, all that pent up aggression is completely unnecessary, and if you've been fruitlessly aiming to concoct one of your own, we've found the perfect place to start. The video posted up after the jump gives a fantastic overview of how the device actually works, and while it's far (very far) from simple, it's nothing the seasoned DIYer couldn't handle on an extended weekend. Give it a look if you're head over heels for PCBs and flashing LEDs (oh, and shameless rock 'n roll).[Thanks, Jeremy]
Networks of carbon nanotubes find use in flexible displays
Carbon nanotubes may very well kill you (okay, so that's very much a stretch), but you'll have a hard time convincing the dutiful scientists at the University of Illinois at Urbana-Champaign to stop their promising research. Put simply (or as simply as possible), said researchers have discovered that "networks of single-walled carbon nanotubes printed onto bendable plastic perform well as semiconductors in integrated circuits." So well, in fact, that the nanotube networks could one day "replace organic semiconductors in applications such as flexible displays." Granted, there is still much to do before these networks are ready for product integration, but you can bet these folks aren't hitting the brakes after coming this far.
Another breakthrough purportedly brings us closer to quantum computing
In reality, quite a bit of time has passed since we've heard of the next great leap in the (seemingly) never-ending journey towards quantum computing, but we're incredibly relieved to learn that at least someone is still out there, somewhere, pressing on. An international team of researchers have reportedly shown that they can "control the quantum state of a single electron in a silicon transistor, even putting the electron in two places at once." Essentially, the team is using tiny semiconductor transistors to "control the state of a quantum system," but there is still a long ways to go before any of this is meaningful. The crew managed to discover a few things by chance, yet to create a quantum computer, they would need to "position atoms of arsenic (or some other material) in the transistors more reliably." For those of you way too geeked out, fret not -- we'll let you know when all of this technobabble finally amounts to something.[Thanks, Chris]
Machine Collective reveals modular prototyping platform
While Bug Labs may have brought modular gadget kits to the forefront, you won't find us kvetching about yet another formidable opponent. Machine Collective has just launched a website to showcase its modular prototyping platform, which essentially consists of a number of interchangeable I/O modules "designed to work with development platforms such as Arduino and Wiring." Needless to say, the possibilities for DIYers and electrical engineers are pretty much endless here, though you'll have to "wait a few weeks" before excitedly beaming in your order and credit card information.[Via MAKE]
HP creates radical 'memristor' technology, brains explode
"Memristors" are one of several memory technologies that have been theorized and promised in the coming years. HP has made a real memristor, however, and the way solid state memory is created and stored could have just changed forever. First theorized in 1971, memristors are basic circuits like resistors, capacitors, and inductors. These circuits are able to store data by allowing their levels of electrical resistance to fluctuate between high and low, or 0 and 1 to a computer. Like flash memory, they retain that data without power -- except they do it all on one circuit and at the speed of D-RAM. In the end, we could be looking at a whole new kind of storage, as long as someone can figure out how to get these things onto integrated circuits. Nerds hats off, return to your fanboyism -- now.
IBM uses nanotechnology to craft miniscule art
It's not like we haven't seen art on silicon before, nor is IBM any stranger to the more bizarre world of design, but the firm is nevertheless "touting one of the tiniest pieces of art ever made." The project, which consists of an "image of the sun made from 20,000 microscopic particles of gold," was reportedly "etched on a silicon chip wafer" with a process that managed particles some 60-nanometers in diameter. Of course, IBM isn't planning on entering the abstract art business anytime soon, but the achievement could purportedly pave the way for "high-performance transistors in molecular-scale chips" while "leading to a nanotech race inside IBM and rival companies."[Image courtesy of BBC, thanks ssuk]
An effortful DIY alternative to a rumbling DS Lite
Those with loads of disposable income probably wouldn't mind ponying up for the relatively inexpensive rumble cartridge made specifically for Nintendo's DS Lite, but the frugal (and engineering) sets will certainly appreciate Xyzzy's efforts. After dissecting a Pokemon Pinball GBA game and ripping the rumble motor from a salvaged Nokia 5100, he put his circuitry knowledge to work and conjured up a rumble device that fit flush in the DS Lite and cost him nothing more than a little blood, sweat, and tears. Be warned, however, that this guide isn't for the faint of heart (or those who don't natively speak in 1s and 0s), but feel free to tag the read link and get busy if you dare.[Via Joystiq]
Printed organic RFID circuits set to collect statistical data
In order to truly judge the effectiveness (or lack thereof) of a newfangled technology, we all know trial by fire is the only way to go. Hence, it follows logic that about 1,000 printed organic RFID tickets will be tested at the Organic Electronics Conference this September in Frankfurt, Germany. The badges will be converted by Bartsch and are "set to be used to monitor the flow of attendees during the two-day conference and exhibition." Deemed the "first ever printed, low-cost organic tickets," these devices will be trialed in order to judge their data collecting abilities and to show whether or not these would be good candidates for use in "public transportation and logistics" applications. So, for those of you heading over to this here event, make sure you're packin' some sort of RFID jammer when waltzing through the door -- you know, just to give these newb tags an unexpected challenge on their first day at work.
DIYer concocts homegrown GSM-GPS tracking device
As we've seen time and time again, the desire to really know what's going on behind the scenes seems to be a growing trend, and while there's a number of pre-fabricated methods to keep track of your vehicle, mischievous offspring, or straying SO, why not take a little initiative and build an alternative yourself? Thankfully, a crafty DIYer has done just that, and has spelled out the details in order for you to replicate his work. The homegrown device is built around the Telit GM862 GSM-GPS module, and all told, he spent around $286 to scratch the mobile GPS itch. The device is small enough to be crammed into nearly any nook or cranny, and can transmit its position via text message to the owner. So go on, give the read link a visit and bust out your credit card -- just be sure to not let the soon-to-be-tracked individual know what you're up to, capiche?[Via NaviGadget]
Billy the Wizard and others spotted on ESRB
Good news! You can sell that imported European Wii you bought! Conspiracy Entertainment is bringing Data Design's lineup of European budget Wii games to the US, according to the ESRB listings. These are budget Wii ports of Metro3D's budget PS2 games. Let us say it again: budget.So far, four Conspiracy games have been rated for US release: Billy the Wizard (original name: Barry Hatter), Anubis II, Mythmakers: Super Kart GP, and Counter Force. No word on Ninjabread Man yet, and we don't know when any of these will be released. In any case, we recommend preordering now so you won't be stuck in line at 5AM on release day.[Via GoNintendo]
HP inkjet printer kicks out environmentally friendly circuit
It's been nearly three years since we first reported on printable circuit boards, but researchers in the UK are still working to hone the process. Leeds University's Seyed Bidoki was recently able to load a "standard Hewlett Packard inkjet printer with a solution of metal salts and water" and print out an actual electronic circuit. The mysterious "silver salt solution" and vitamin C mixture could be used to "pave the way for safer and cheaper electronics manufacturing," and moreover, this cheap and easy alternative should certainly be a hit with the environmentally conscience crowd. This method utilizes a water-soluble base, which differs from the less green solvents used in polymer ink / graphite paste varieties from before, but even individuals working with the project admit that ousting the current regime will be difficult. Still, the crew is pressing forward with this toxin-free approach, and hopes to elicit the help of "industrial jet printers" before long to speed things up.
Wii circuitry changed to thwart modchips?
Reports are coming in from Taiwan and Germany that Nintendo has updated the Wii's motherboard with its latest shipments of the console. According to MaxConsole, one of the solder points has been removed from the altered board, shutting out quicksolder modification chips like WiiKey. Other similar tools that don't use the missing solder point should not be affected. DigiTimes suggests that these changes to the circuit layout were made with the sole intent of preventing piracy by blocking these warranty-voiding installations. If that's the case however, why did Nintendo only take steps to block just the WiiKey, a modchip that was released only several weeks ago?There were similar concerns in the past about Mario Kart DS updating the Nintendo DS' firmware as an anti-piracy measure, but it was quickly discovered that the handheld was only saving its WiFi settings. It seems far more likely that Nintendo has had the Wii's revised motherboard planned for months, and that locking out any modification methods was an unintended result.
Daring DIY'er devises homegrown heart monitoring device
While there's already a plethora of safe, proven methods to monitor your heart rate, there's just no satisfaction in buying an off the shelf BioShirt when you know you possess the skills (and spare time) to craft a system of your own. Interested in making his own mark in biomedical engineering, a crafty individual set out to build his own electrocardiograph for nothing more than fun, but rather than keeping his homegrown work all to himself, he busted out a set of instructions in order for us less inventive souls to replicate the process. Aside from creating an ECG board, reading results with LABView, and having the nerve to actually strap leads to your body and hope that you don't electrocute yourself, there's still a good bit of coding and behind the scenes work necessary to pull this off. So if you never got around to going to medical school, but you know you've got the DIY skills to operate a heart monitoring system in your home office, be sure to hit the read link and read that blurb about "destroying your nervous system" real carefully.[Via MAKE]
Sony's 1/1.8-inch high-speed CMOS sensor outputs 60fps
Thankfully, it looks like Sony has come through yet again, and while it wasn't exactly in the timeliest of manners, the high-speed CMOS sensor that it promised would deliver 60fps of video output is finally upon us. The 1/1.8-inch IMX017CQE sensor boasts 6.4-megapixels of resolution and the uncanny ability to "output this resolution at 60 frames per second (a data rate of around 384 megapixels per second)." In layman's terms, this chip has the ability to capture full motion video and grab high-quality stills without dropping a single frame, giving users a seamless transition between the two. Additionally, the 1/1.8-inch size and its ability to deliver 300 frames per second at lower resolutions moves it a bit further from the pack, not to mention the 12-bit A/D converter for each column. No word just yet on when these video-centric chips will hit Sony's CyberShot lineup, but it's an awful lot closer to reality than the last time we caught wind of it. [Warning: PDF read link][Via DPReview]
